STANLEY 70-944E 14mm Combination Spanner in City name

Buy STANLEY 70-944E — Pack Quantity, Price and GST

The listed product price applies to the 10-piece pack. It is not the price of a single spanner, and the pack does not contain ten different sizes.
Review the current GST-inclusive price and tax breakdown on the exact product listing. Choose the number of packs required for your technicians, toolroom or maintenance purchasing needs.
Enter your delivery pincode to check serviceability for the intended City name destination.
Check Current Price & Buy STANLEY 70-944E

STANLEY 70-944E Technical Specifications

The STANLEY 70-944E is a conventional 14mm combination spanner designed for use on appropriately sized metric hexagonal fasteners.

Detailed Dimensional References

The STANLEY specification drawing provides the following dimensional measurements for the 70-944E:

These labels correspond to the dimensional positions shown in the product drawing.
For work involving restricted access around a housing, bracket or other assembly, compare the actual drawing with the available clearance. The nominal 14mm size alone does not describe the complete outside dimensions of the tool head.

Open-End and Ring-End Function

A combination spanner provides two engagement styles for the same nominal fastener size.

Open-End Jaw for Lateral Access

The open-end jaw can be placed onto a compatible 14mm hexagonal nut or bolt head from the side.
This is useful when a shaft, housing or nearby component prevents a ring end from being lowered over the fastener.
The STANLEY 70-944E includes an anti-slip open-end design. Even with this feature, the jaw must fit correctly and be fully engaged before force is applied.

Ring End for Enclosed Fastener Engagement

The ring end surrounds more of the fastener head than the open end.
Where there is adequate clearance, the ring end provides another way to loosen or tighten a properly sized fastener. Fully seat it over the hexagonal head before turning.
Avoid using the ring end at an angle or when it cannot engage the fastener properly.

Maxi-Drive Profile

STANLEY describes its Maxi-Drive feature as a design intended to reduce fastener rounding.
Proper use remains important: choose the correct wrench size, check that the fastener faces are in usable condition and apply manual force only after the tool is correctly seated.
The Maxi-Drive design is not a substitute for correct fitment and does not establish a calibrated torque rating.

How to Check 14mm Fastener Compatibility

The 14mm size refers to the distance across opposite, parallel flats of a suitable hexagonal nut or bolt head.
This measurement is not the same as the diameter of the bolt's threaded shank.

Identify the Actual Across-Flats Size

Before purchasing, measure the hexagonal head or check the engineering drawing for the fastener.
Bolts described by metric thread sizes such as M8 or M10 may have different head dimensions depending on their standard and design. The thread designation alone is insufficient to confirm whether a 14mm spanner is suitable.
Use STANLEY 70-944E only when the fastener's engagement size matches the tool.

Check Clearance and Handle Movement

The 70-944E has an overall length of 180mm.
Check that there is enough space to position the selected head correctly and move the handle through the required angle without interfering with other components.
For deeply recessed fasteners, a properly sized socket and handle may be more suitable than a flat combination spanner.

Avoid Loose-Fitting Substitutes

Do not substitute a 14mm spanner for a smaller or larger head simply because it appears close in size.
A loose fit can damage the fastener corners or cause the tool to slip. Metric and imperial wrench sizes should also not be treated as interchangeable without confirming the actual measurements.

Applications for STANLEY 70-944E

The spanner is intended for general manual fastening tasks involving compatible 14mm hexagonal fasteners.

Equipment and Machinery Maintenance

Maintenance technicians may use this size for suitable accessible fasteners on machine brackets, covers, supporting structures and mechanical assemblies.
The exact task must be assessed for fastener size, access, required tightening method and relevant equipment instructions.

Automotive and Fleet Workshop Work

Automotive workshops encounter many different head sizes across brackets, fittings and mechanical assemblies.
The STANLEY 70-944E is an option where the actual hexagonal head measures 14mm across flats and a manual combination spanner is suitable.
It should not be selected only on the basis of a vehicle type or a general automotive application.

Fabrication and Installation Tasks

A 14mm combination spanner may assist with compatible mechanical fastening during bracket fitting, frame assembly and equipment installation.
For load-bearing or safety-critical connections, follow the specified fastener grade, installation process and tightening requirements.

Toolroom and Technician Allocation

Where several technicians or workstations regularly require a 14mm spanner, a pack of ten identical tools can support planned tool allocation.
Check whether the requirement is for ten copies of one size or for a variety of sizes before ordering. A mixed-size spanner set is a different product.

Proper Use and Maintenance

Inspect Before Use

Check the open-end jaws, ring profile and tool body for wear, distortion or cracking.
Use the spanner only on a matching, sufficiently intact fastener head. A heavily rounded nut or bolt may require a suitable specialist removal tool.

Do Not Use Improvised Extra Leverage

Do not strike this conventional spanner with a hammer or extend the handle with a pipe to apply additional force.
Improvised leverage may overload the tool, damage the fastener or create an injury risk.

Use a Torque Wrench for Specified Tightening Values

The 180mm handle allows manual turning force, but the STANLEY 70-944E is not a calibrated torque wrench.
It does not indicate how much torque has been applied or stop at a chosen tightening value.
Use the appropriate torque-control equipment when an assembly procedure specifies tightening torque.

Observe Electrical Safety Requirements

This model is not established as a certified insulated tool for energized electrical work.
When working around electrical equipment, follow the appropriate isolation procedure and use tools rated for the job.

Keep the Tool Clean and Dry

Wipe away dirt, grease and moisture after use. Store the spanner in a dry toolbox, rack or organized tool station.
Inspect its working ends regularly and remove damaged tools from service.

Combination Spanner or Another Tool?

The 70-944E is a fixed-size manual combination spanner, not an adjustable or ratcheting wrench.

Order STANLEY 70-944E for City name

Confirm the Pack Quantity

The Indus MegaMart selling unit is a pack of ten identical STANLEY 70-944E 14mm combination spanners.
One complete pack contains ten tools; two complete packs contain twenty.
Check the quantity displayed in the cart, along with the selected size and model, before confirming the purchase.

Review GST and Business Invoice Details

Check the current GST-inclusive pack price and the corresponding tax breakdown on the product listing.
Generated Indus MegaMart purchase invoices contain the company's GST number. For business purchasing, verify the billing and delivery details entered with your order.

Check City name Delivery Pincode

Enter the delivery pincode on the exact National Product Page to check serviceability.
Delivery availability depends on the actual destination and the stock-dependent order conditions.

Delivery Based on Available Stock

For serviceable delivery destinations, Indus MegaMart accepts orders and payments even when available stock is insufficient or zero.
The applicable delivery windows are:

• Ordered quantity less than or equal to available stock: Delivery within 7 days.
• Ordered quantity greater than available stock: Delivery within 7–14 days.
• Available stock is zero: Orders and payments are accepted, with delivery within 7–14 days.

Review the current stock presentation and your required quantity at the time of ordering.

Explore Other Tool Requirements

If your purchasing list includes different wrench sizes, sockets or other manual tools, browse the Spanners, STANLEY and Hand Tools collections.

Frequently Asked Questions

What is the size of STANLEY 70-944E?

The STANLEY 70-944E is a 14mm metric combination spanner intended for compatible hexagonal nuts and bolt heads measuring 14mm across flats.

What is its overall length?

The STANLEY 70-944E has a listed overall length of 180mm.

How much does one STANLEY 70-944E spanner weigh?

The manufacturer-branded technical table lists a weight of 0.088kg, equivalent to 88g, per spanner.

What material is the spanner made from?

It is made from chrome-vanadium steel with a matte finish. It also features an anti-slip open-end jaw and Maxi-Drive fastener engagement design.

Does the Indus MegaMart price cover one spanner or ten?

The listed Indus MegaMart selling unit is a pack of ten identical STANLEY 70-944E 14mm spanners.

Is the pack a set of ten different sizes?

No. All ten pieces are the same 14mm model. A multi-size combination spanner set is a separate product type.

Will a 14mm spanner fit every M8 or M10 bolt?

No. The metric thread designation does not, by itself, determine the bolt head's across-flats measurement. Confirm the actual head is 14mm.

What is the difference between the two ends?

The open end allows side access to a compatible fastener. The ring end surrounds more of the head and can provide an alternative engagement when it can be fully seated.

Is STANLEY 70-944E a ratcheting or adjustable spanner?

No. It is a conventional fixed-size combination spanner with an open-end jaw and matching ring end.

Can this model replace a torque wrench?

No. It has no calibrated torque-setting or measuring mechanism. Use a suitable torque wrench when a specified tightening torque is required.

Can I place an order when available stock is zero?

Yes. Indus MegaMart accepts orders and payments even at zero stock. For a serviceable pincode, the stated delivery window in that situation is 7–14 days.

How do I purchase this spanner for City name?

Open the exact Indus MegaMart product page, check the GST-inclusive ten-piece pack price, choose the required quantity, enter the destination pincode and complete the order using the available purchase controls.

Buy STANLEY 70-944E 14mm Combination Spanner Online

The STANLEY 70-944E is a 180mm chrome-vanadium steel combination spanner with a 14mm open end and ring end for suitable metric hexagonal fasteners.
Indus MegaMart offers this exact model in a ten-piece pack for workshop maintenance, toolroom allocation and general mechanical purchasing.
Confirm the fastener size, review the current GST-inclusive pack price and check City name pincode serviceability before ordering.
View Current Price & Order STANLEY 70-944E 14mm Combination Spanner